Polyester Fiberglass Composite Mat Polyester Fiberglass Composite Mat ( Composite Paving Mat ) has a combination structure of Polyester Mat + Fiberglass Scrim + Fiberglass Mat. The strong fiberglass mesh embedded between polyester mat and fiberglass mat is the key to its performance. The...
Polyester Fiberglass Composite Mat
Polyester Fiberglass Composite Mat (Composite Paving Mat) has a combination structure of Polyester Mat + Fiberglass Scrim + Fiberglass Mat. The strong fiberglass mesh embedded between polyester mat and fiberglass mat is the key to its performance. The fiberglass mat on the bottom side minimizes the mat shrinkage during the overlay process, the polyester mat on the upper side minimizes the possibility of being punctured by some sharp objects. Being reinforced by fiberglass mesh, the composite paving mat have strong tensile strength and low elongation, which extends the life of pavement overlays through the delay of reflective cracking. The composite Paving Mat provides the highest tensile strength with an elongation lower than 5%, making it a strong, commercially available and full coverage paving mat or fabric.
The product also serves as an effective moisture barrier equal to paving fabrics and mats. The unique, non-woven, fiberglass matrix structure of the Composite Paving Mat allows asphalt binder to fully penetrate and fill voids within the fabric, limiting moisture infiltration and preventing water from infiltrating into the granular layers of the pavement structure.
Composite Paving Mat creates innovative solutions to help the paving projects to go smoothly and provides superior performance on airport runway, super highway, parking area and business lots.
<table width="100%" border="0" cellspacing="0" cellpadding="0" class="table"
Polyester Fiberglass Composite Mat
Polyester Mat + Fiberglass scrim +
Polyester Mat +
Fiberglass scrim +
Area Weight (g/M2)
Fiberglass Mat Weight (g/M2)
Polyester Mat Weight (g/M2)
Mesh Open (ends/cm)
MD & CD yarns (Tex)
Binder Content (%)
Tensile Strength MD（N/5cm）
Tensile Strength CD（N/5cm）
Application: Use as excellent paving mat and other geotechnical material.
◆ Delays reflective cracking
◆ Provides a Moisture Barrier
◆Easy installation and Less Maintenance
◆Fully Millable and Recyclable
◆Low risk of product shrinkage during the overlay process
◆Tensile strength, roll length, width and area weight can be tailored according to client’s demand.
Instruction to use the polyester fiberglass paving mat:
◆ Remove dirt, gravel and dust from the pavement to assure good adhesion between asphalt and pavement.
◆ If the road is damaged, it must be repaired to make the surface of the road hard and smooth.
◆ For a good result, the asphalt binder that will be used to adhere the Paving Mat to the road must be hot asphalt, but not emulsified asphalt.
◆ The temperature of hot asphalt should be between 163℃ and 204 ℃.
◆ When the hot asphalt covered the road, the Composite Paving Mat must be overlaid onto the hot asphalt before the asphalt lose it’s mobility so as to assure the mat fully soaked by asphalt and effectively provides a moisture barrier.
◆On installation of the Composite Paving Mat, the air temperature must be higher than 4 ℃.
In order to achieve optimal results, here we provide some Notes on installation of Composite Paving Mat:
◆Composite Paving Mat must be installed on hot asphalt. We recommend the following asphalt. AC-20; PG64-22; AR8000 +, or asphalt with penetrate rates 60-80. In extremely hot summer, we recommend to use asphalt with high viscosity, such as AC-30; PG67-22; AR8000 +, or asphalt with penetrate grade 40-60.
◆ The best ratio of asphalt is 1.1 liters / square meters paving mat, but subject to project site situation during the installation, the ratio can be between 1.0-1.3 liters / square meters. According to different area weight of the Composite Paving Mat, the ratio of asphalt should be adjusted accordingly. During the asphalt delivery, we do not advise to heat the asphalt above to a temperature higher than 204 ℃, because this would hinder the pre-mature of liquid asphalt.
◆ Handle the Composite Paving Mat with care during the installation, the paving mat might be damaged or it may cause bad result if the paving mat drop down from the installation machine.
◆During the installation, if it forms a stripe bigger than 2.5cm in any direction, the stripes must be cut and overlaid, and the two layers of paving mat must be fully covered by asphalt so as to assure the two layers of paving mat fully soaked in the hot asphalt. Use roller to press the paving mat or use brush to clear out bubbles in the paving mat to ensure the paving mat fully adhered to the road. When covering the hot asphalt to the road, the width of asphalt should be 4 inch more than the width of paving mat. Since the paving mat can not be curved, for the winding area of the road the paving mat can be cut into several pieces and be installed to the road manually or mechanically.
◆For the connection of two pieces of paving mat: the two pieces of paving mat must be overlapped together. In the longitudinal direction the width of overlapped area must be at least 10.2cm; and in the lateral direction, the width of overlapped area must be at least 5.1cm.
◆ If the installation machine or other vehicles have to drive on the paving mat, it should not turn directions frequently nor suddenly so as to avoid damaging the paving mat. Do not scatter sand or other object on the paving mat; to avoid asphalt sticking to the tire of the machine, do not minimize the ratio of bitumen.
Previous: No Information
Next: Fiberglass Composite Mat