Fiberglass mesh tape is woven by C-glass fiberglass yarn and coated with alkali-resistant coating and self-adhesive glue. The fiberglass mesh tape is designed for use with joint compounds to reinforce gypsum board joints, repair drywall, etc. The fiberglass mesh tape has good performance with good softness, high stickness, and easy application.
Fiberglass mesh tape is woven by C-glass fiberglass yarn and coated with alkali-resistant coating and self-adhesive glue. The fiberglass mesh tape is designed for use with joint compounds to reinforce gypsum board joints, repair drywall, etc. The fiberglass mesh tape has good performance with good softness,high stickness , and easy application.
The fiberglass mesh tape is used to cover seams in the drywall construction, also be used for wall and ceiling problems.
Fiberglass mesh tape can save considerable time and eliminate one step of mudding when combining the self-adhesive mesh tape with a setting compound. The fiberglass mesh tape's open weave construction will allow moisture to evaporate evenly and much more quickly without the worry of bubbles and blistering when compared to paper tapes.
It owns good performances, like good softness, high stickiness, and easy application, it gives you the best solution for the wall problems like wall cracks, plasterboard joints, wall holes, etc. and it is the ideal material for the drywall and ceiling problems.
The fiberglass mesh tape conceals and reinforces gypsum board joints. The tape is buffed on both sides to ensure the best working qualities and bond.
Good performance of alkaline-resistance
High tensile strength and deformation-resistance
Excellent self-adhesive performance
Simple and easy to be applied
Mesh size: 2.85 x 2.85mm (9 x 9 mesh), 3.2 x 3.2mm (8 x 8 mesh)
Width: 50mm, 100mm, 150mm, 200mm, 1000mm, 1200mm, 1500mm, etc.
Length of roll: 20 m to 900m, Any demand length is available, or according to client requirements
Colors available: white, yellow, grey, silver, blue, black, etc.
Inner packing: shrink packing or plastic bag,
Outer packing: 24 rolls or 54 rolls or 72 rolls/carton or pallet packing
1. Failure to completely fill the joint may result in cracking.
2. For best results, use a setting-type compound.
Cement-coated fiberglass mat will be loaded into the container in the factory, then be delivered to the seaport, and finally be shipped to the Customer's port by MSK, MSC, CMA, COSCO, YANG MING, APL, etc.
LC, T/T, CAD, PAYPAL, WESTERN UNION, ETC.
If the customer meets any problem with technic, Nanjing EFG CO., LTD will supply relative knowledge to help the customer find the best solution, and can send a technician to the customer's factory for guidance if necessary.
1. Who we are?
we are NANJINGEFG CO., LTD
2. What do we do?
We are the professional and best manufacturer of fiberglass products in China.
3. What is our goal?
Create greater value for our customers.
4. Why choose us?
We focus on the fiberglass industry for 20 years.
We have 20 years of export business experience.
We are more professional and efficient.
5. What is our website?
6. Why choose our fiberglass tape?
Our fiberglass tape represents a more professional service and an efficient way of working, the most important thing is to create greater value for our customers.
7. What I can do for you?
Save your time, save your costs and create maximum benefits for you
8. What are the advantages of our products?
A Grade of top quality, full size, and higher stability
9. What are our talent advantages?
We have 20 years of experience in fiberglass export work.
We have more professional product knowledge.
We understand the target market better.
We are the best partner for you.
Some information on fiberglass repairing:
What should I know about fiberglass repair?
There are a few fundamental principles that, once understood, allow most composite repairs to be completed successfully. Successful repairs allow you to extend the life of a part or mold and save you the cost of replacing your composite part. Start by considering these three main principles of composite repair:
Repairs differ from the original part — The first principle you must understand is that structural repairs are made by a different process than the original piece. When a composite part is initially manufactured, its resin cures bonding both chemically and physically with the reinforcement fabric resulting in a single unit, regardless of the number or orientation of the plies of fabric. This is referred to as the primary structure or bond, and it is the strongest type of bond that can exist within a composite part.
Once a part is damaged, all repairs become secondary bonds attached to the original primary structure. This means all repairs are dependent upon physical bonding to the surface of the original primary structure (more on this later). For this reason, fiberglass repairs rely upon the adhesive quality of their resin for their strength—the strength of the physical bond to the primary structure. Because of this, the resin used for the repair should be just as strong as the resin used to fabricate the part. In fact, resins with strong adhesive properties are sometimes used for repairs.
The increased surface area will increase the strength of composite repairs — Since fiberglass repairs depend upon surface adhesion (physical bonding) of the repair to the primary structure, increasing the surface area of the bond line will increase the strength and durability of the bond—and by extension the part or repair.
Typically, the method employed to increase the surface area is taper or scarf sanding. This type of sanding means the area next to the damage is sanded away gradually, generally resulting in approximately ½—¾ of an inch of area per ply of composite laminate. Scarf sanding is usually done with a high—speed compressed—air power sander. Since most composite structures are fairly thin, this is a gentle process. The size of the taper, relative to the thickness of the laminate, is expressed as a ratio. Generally, the stronger or more critical the repair needs to be, the larger the ratio. Structural repairs usually require a gentler taper, with a ratio of 20:1 up to 100:1.
An alternative method employed to increase surface area is step sanding. This procedure defines the size of the inner repair, then removes surrounding materials at a width of ½" per ply of the part, working towards the part surface. This results in considerable growth of the repair surface and allows the fiber orientation to be evident in each step.
Both methods are acceptable for the majority of composite repairs, though most consider scarfing to be easier, and it’s generally considered better. Stepping results in abrupt edges and butt joints in each repaired ply. It is also hard to step sand without cutting through, potentially damaging the underlying plies.
You should match your repair to the original part when possible — While your composite repair is different than your original part, it is recommended that you duplicate the thickness, density, and ply orientation of the original laminate when making your repair. This will help to maintain the functionality of the part. More is not always better—in this case, if your repair is thicker than the original part, it will almost certainly be stiffer, regardless of the material in use. Introducing various strengths within a part can cause unintended stress points, eventually leading to material fatigue or failure. It is better to carefully replace every ply that has been removed in the damaged area with identical material, placed in the same orientation when possible. This ply—for—ply replacement approach guarantees the repaired structure can withstand the same loads as the original, and that it will disperse loads as intended.
With these three fundamental principles in place: Repairs Differ from the Original Part, Increased Surface Area Increases Strength, and Repairs Should Match your Original Part; you have the foundation for understanding the sequences for repairs. As stated earlier, we are going to provide detailed steps for both structural fiberglass repairs and general cosmetic composite repairs. Keep in mind that these are general steps, and certain applications may call for additional steps or slight variances in approach.
Previous: Fiberglass Seam Tape